标准丨CISPR 15:2018 Edition 9标准更新

作者:

来源:

2018年11月05日

标准丨CISPR 15:2018 Edition 9标准更新

 

CISPR15:2018有很多重要的变化,标记黄色部分的非常重要的,EN55015:2018很快也会发布

具体的变化请见如下:

Within the remainder of this document, whereverthe term "lighting equipment" or "EUT" is used, it is meantto be the electrical lighting and similar equipment falling in the scope ofthis document as specified in this clause. This ninth edition cancels andreplaces the eighth edition published in 2013 and its Amendment 1:2015. Thisedition constitutes a technical revision. This edition includes the following significanttechnical changes with respect to the previous edition:

最新版的灯具产品标准CISPR15:2018 edition 9.0已经在2018年5月15日发布,第九版取代了2013年出版的第八版及其修订版本A1:2015。这个版本是一个技术版本。本版本包括以下与前一版本相比的重大技术变化。

a)full editorial revision and restructuring;

1.全部重新编辑修改及重组

b)the restriction to mains and batteryoperation is deleted in the scope;

2.在适用范围中取消了对于电源和电池运行设备的限制,如下截图:

 

新标准截图

旧标准截图

c)radiated disturbance limits in the frequency range 300 MHz to 1 GHz have beenintroduced;

3.辐射测试的频率有延伸,增加了300MHz1GHz辐射骚扰的限值。

d)theload terminals limits and the CDNE (alternative to radiated emissions) limitshave changed;

4.负载端的限值有变化(参考本文6.b),CDNE的限值也有变化。

 

CNDE 新限值截图

新标准规定了新的CDNE法,1. 仅适用于带时钟的EUT频率低于或等于30 MHz;对于CDNE方法,最大尺寸的EUT为3 m x 1 m x 1 m(长x 宽x 高)

 

旧标准截图

e)deletionof the insertion-loss requirements and the associated Annex A;

5.删除了插入损耗的要求和与其相关的附录A

f)introduction of three basic ports: wired network ports, local wired ports andthe enclosure port;

6.取消原有的负载端,控制端,引入了三种新的叫法:有线网络端口,本地有线端口,以及外部壳体端口

 

a.有线网络端口这个端口可以直接t通过线缆连接到一个网络,并且通过这个线缆耦合电磁骚扰到这个网络。包括AC/DC电源端,以及其他可以直接连接到公共网络的端口。增加了电流法的限值,table 3

b.本地有线端口:这个端口可以直接连接线缆,但是不能连接到一个网络,而且长度大于3米,或者通过一个辅助设备间接连接到网络,分为两种等级:

b1.间接连接到公共网络,需要通过一个辅助设备,主要是ELV灯具;

b2.不能直接和间接连接到网络,可以连接一根等于和长于3米的线缆。

 

注:旧标准没有区分限制性和非限制性ELV灯具的限值,也没有电流法的限值,仅有一个负载端的限值,table2b

 

注:以下新标准是限值:

注意:ELV; 限制性ELV灯具的定义:

ELV:电压不超过AC 50VDC 120V, 不包括通信和数据传输在内的设备。

限制性ELV灯具:对于POWER SUPPLY的类型和cable的长度有特别的限制。

g)introduction of a moretechnology-independent approach;

7.引入了更多独立的技术方法。

h)replacement of Annex B (CDNE) by appropriatereferences to CISPR 16-series of standards;

8.新引用了辐射发射的替代方案CDNE,该测试方法取代原有的CDN法:(参考本文第4)

-1规定了CDNE法,仅适用于带时钟的EUT频率低于或等于30 MHz。

-2对于CDNE方法,最大尺寸的EUT3 m x 1 m x1 m(长 x  x 高)

i)modified requirements for the metal holes ofthe conical housing;

9.修改了锥形外罩的金属空的要求。

j)newconducted disturbance measurement method for GU10 self-ballasted lamp;

10.对于GU10灯头的自整流灯,增加了新的传导干扰的测量方法

k)addition of current probe measurement method and limits for various types ofports (in addition to voltage limits and measurement methods);

11.对于各种类型的端口增加了电流探头的测试方法和限值。

l)introduction of the term ‘module’(insteadof independent auxiliary) and requirements for measurement of modules using ahost (reference) system;

12.引入了module属于替代了independentauxiliary,要求modules的测量要使用一个主机系统。

m)modified specifications for stabilization times of EUTs;

13.修正了部分灯具类产品测试前所需求的老化时间,并明确说明了使用LED/OLED技术的灯具类产品,测试前不需要进行老化,具体可参见法规7.7.2章节;修改了产品稳定的时间的规范,7.8章节。